HENAN GNEE NEW MATERIAL CO., LTD
86-372-5055135

Notes on Customizing Aluminum Roof Siding Panels

May 20, 2025

Alloy and Temper Selection Comes First

Custom aluminum roof siding panels are ordered by alloy, temper, gauge and coating system, and the alloy decision fixes every later choice. General roofing, soffit and gutter work in inland atmospheres is normally produced from the Al-Mn-Mg grades 3004 and 3104, which combine moderate strength with good formability for roll forming and folding. For coastal sites, industrial atmospheres and heavy salt spray, a higher magnesium grade such as 5052 or 5754 is selected, and for the most severe marine and chemical exposure a grade with magnesium in the 3.5 to 4.5 percent range, corresponding to EN AW-5083, is the appropriate choice.

Grade family Typical temper Service environment Notes
EN AW-3004 / EN AW-3104 H24, H26 Inland roofing, soffit, rainwater goods Manganese and magnesium give strength with good forming
EN AW-5052 / EN AW-5754 H32, H34 Coastal and industrial roofing, cladding Higher magnesium content improves salt spray resistance
EN AW-5083 H116, H321 Severe marine and chemical exposure Magnesium 3.5 to 4.5 percent; highest corrosion resistance of the group

Feedstock quality is as important as the grade number. Coil should be rolled from primary ingot with controlled iron, silicon and tramp element levels rather than from uncleared recycled material, and the mill test certificate must be checked against the chemical and mechanical requirements of EN 573-3 and GB/T 3190 before the coil is released. Panel strength and coating adhesion both depend on a clean, uniform substrate, so surface finish and the absence of rolled-in oxide are part of the purchase specification.

Thickness, Coating Build and Forming Limits

Thickness is driven by wind load, span and fixing detail. Panels in coastal zones or areas of high wind pressure are specified at 0.6 millimetres and above, while inland conventional areas normally use 0.4 millimetres and above. Sections that are arched, folded or otherwise shaped should be locally thickened into the 0.8 to 1.2 millimetre range so that the formed edge keeps its strength after bending.

Coating system Typical dry film thickness Intended use
Polyester coil coating 20 to 25 micrometres Inland roofing with moderate UV exposure
Fluorocarbon two-coat 25 micrometres or more on the weathering face Coastal and high UV exposure, colour retention
Fluorocarbon three-coat 35 micrometres or more on the weathering face Severe exposure and premium architectural work

The thickness figures follow the fluorocarbon coating performance levels widely used in architectural work, where a two-coat system carries a minimum dry film thickness of about 25 micrometres and a three-coat system about 35 micrometres on the exposed face. Coating build below those levels shows up later as chalking, colour shift and edge creep at cut lines, so the coating weight should be verified on the finished panel rather than on the flat coil alone.

Design Planning and Dimensional Control

Customisation starts with measurement. The building outline should be captured by laser scanning or a checked dimensional survey, the three-dimensional model should be closed to plus or minus 3 millimetres, and the parameters of every shaped area should be marked separately on the drawing set. The fabrication drawings then have to state the lap length, the expansion allowance and the fixing pattern explicitly.

Lap length: end and side laps of 80 millimetres or more, increased at low roof pitches where wind-driven rain is a risk.

Thermal movement: designed expansion joints of 5 to 10 millimetres, with the fixing detail left free to slide so the panel can move without buckling.

Slope and fixings: roofs at 10 degrees or less take a concealed locking system, while slopes above 30 degrees need additional wind-resistant clamps at every fixing line.

Rooftop equipment: where photovoltaic arrays will be mounted, the base zone is prepared with reinforced purlins designed for a load above 500 kilograms per square metre.

Slope also governs the water path and the position of the joints. Getting the lap direction, the expansion allowance and the fixing zone onto the drawing before cutting is what prevents the two most common site complaints: oil-canning on the flat of the panel and open laps after the first season of thermal cycling.

Substrate, Framing and Sealing

Panel performance is limited by the substrate and the framing under it. A concrete base is ground or filled to a flatness of 3 millimetres over a 3 metre straightedge, and a timber base is treated twice with preservative and dried to a moisture content below 12 percent before any panel is laid.

Framing: horizontal purlins at centres of 500 millimetres or less, with a closer row at 300 millimetres at eaves, ridges and openings, and a 30 percent increase in fixing density along the eaves line.

Fasteners: A2 or A4 stainless steel anchors or self-drilling screws, tightened to a torque of 15 to 20 newton metres so the panel is clamped without being distorted at the fixing point.

Joint sealing: modified silane sealant with an elastic recovery of 90 percent or more for movement joints, and a weather-resistant sealant bead at least 10 millimetres wide between flashings and the wall.

Sealant choice has to match the movement expected. A rigid or low-recovery sealant simply cracks the first time the panel expands at summer temperatures, so elastic recovery is specified and verified from the supplier data sheet rather than from the label alone.

Acceptance, Testing and Special Requirements

Acceptance of a completed system combines visual inspection with simple field tests, and the results should be recorded panel by panel. During the hot period, the reserved expansion joints are checked to confirm that the gap change stays within 2 millimetres. Watertightness is tested by applying a simulated heavy rain flow of 3 litres per minute per square metre for 30 minutes and confirming that no seepage appears on the underside or at any lap. On completion, the finished panel is compared with the approved sample for colour difference, coating thickness and joint accuracy, with a colour difference limit of about 1.5 units and a measured coating thickness of at least 90 percent of the design value.

Special finishes follow the same logic. Antique or corrugated decorative panels are produced by anodising, with an oxide film of 15 micrometres or more and a colour fastness of grade 8 or better. Roofs in extreme climate zones can use a composite panel with a rigid polyurethane or polyisocyanurate core of 45 kilograms per cubic metre or more to combine sound reduction with thermal insulation. Where photovoltaics are planned, a mounting rail is installed as part of the roofing works so that no later drilling is needed, which removes the most common cause of waterproofing failure on integrated arrays.

Frequently Asked Questions

Q: Which aluminum alloy is best for coastal roof panels?
A higher magnesium grade such as EN AW-5052 or EN AW-5754 is standard for coastal work, and EN AW-5083 is used where salt spray and chemical exposure are most severe.

Q: What sheet thickness is required?
Use 0.6 millimetres or more in coastal or high wind pressure areas and 0.4 millimetres or more inland, with local thickening to 0.8 to 1.2 millimetres at arched and folded sections.

Q: How much expansion allowance should be designed in?
Expansion joints of 5 to 10 millimetres are typical, and the fixing detail must allow the panel to slide so that the joint can release the stress developed on a hot day.

Q: Which fasteners should be used?
Stainless steel anchors or self-drilling screws tightened to 15 to 20 newton metres, so that panels are held firmly without being crushed at the fixing point.

Q: How is a completed roof tested for leaks?
A flow of 3 litres per minute per square metre is applied for 30 minutes and the underside is inspected; any seepage at a lap or flashing fails the test.

Q: What dry film thickness should the coating have?
A fluorocarbon two-coat system should reach at least 25 micrometres and a three-coat system at least 35 micrometres on the weathering face.

Q: Can photovoltaic mounts be added later?
They are far more reliable when a mounting rail is built into the roofing package, because later drilling through a finished panel is the main cause of leaks on integrated arrays.