HENAN GNEE NEW MATERIAL CO., LTD
86-372-5055135

Aluminum Bar Supplier & Manufacturer | Custom Sizes

 

GNEE supplies aluminum bars in five cross-sections—round, flat, square, hex, and rectangular—across 1xxx, 3xxx, 5xxx, and 6xxx series alloys. We serve buyers who need stock sizes, cut-to-length pieces, or material produced to a drawing, and we confirm the production, outsourcing, or trading route for each order before it is placed.

 

To request a quote, send the shape, alloy and temper, dimensions and length, surface finish, quantity, and target standard. We confirm the specification and lead time, then return a written quote with MOQ, price, and documentation.

Request a quote for aluminum bars

 

Aluminum Bar Types

 

Aluminum Round Bar

Aluminum Round Bar

Aluminum round bar for shafts, pins, bushings, and cnc-turned parts. common in 6061, 6082, and 6063.

read more
Aluminum Flat Bar

Aluminum Flat Bar

Rectangular-section strip for brackets, frames, and base plates. Width × thickness in a wide range of alloys.

read more
Aluminum Square Bar

Aluminum Square Bar

Equal-side section for fixtures, spacers, and structural members. Easy to saw, drill, and machine.

read more
Aluminum Hexagonal Bars

Aluminum Hex Bar

Hexagonal bar for nuts, fasteners, and wrench-held components. Usually supplied in 6061 or 6082.

read more

 

Aluminum Bar Alloys and Tempers

Common Aluminum Bar Alloys

We stock and produce to order a range of wrought alloys. The table below lists typical room-temperature properties so buyers can shortlist candidates; exact lot values are stated on the EN 10204 3.1 Mill Test Certificate.

Alloy (series) Common temper UTS (MPa, typical) Yield (MPa, typical) Density (g/cm³) Primary characteristic
1050 Aluminum Rod(1xxx) O / H14 75–115 35–105 2.71 High formability, good conductivity, corrosion resistance
3003 (3xxx) O / H14 145–200 55–175 2.73 Formability + corrosion resistance, welded parts
5052 (5xxx) O / H32 170–280 65–250 2.68 Marine corrosion resistance, weldable
5083 (5xxx) O / H111 / H116 270–350 120–280 2.66 High marine corrosion resistance, weldable, not heat-treatable
6061 Aluminum Rod(6xxx) T6 / T651 260–310 240–275 2.70 Versatile, weldable, heat-treatable
6063 (6xxx) T5 / T6 150–240 110–215 2.70 Architectural sections, lower strength than 6061
6082 (6xxx) T6 290–340 250–300 2.70 Structural, weldable, higher strength than 6061

Values are typical for the listed temper per ASTM B211 / B221 and EN standards and are a guide only; the EN 10204 3.1 MTC governs the delivered lot. Not every alloy is held in every shape and size — confirm availability for your combination.

 

Choosing the Right Aluminum Alloy and Temper

Temper changes strength, machinability, and weldability, so alloy alone is not enough. For machined parts needing good strength and weldability, 6061-T6 or 6082-T6 are common choices. For marine or welded structures, 5083-H111 / H116 is widely used.  Send us the load, environment, and weld plan and we recommend the alloy-temper pair.

 

Aluminum Bar Sizes and Specifications

Available Aluminum Bar Cross-Section Dimensions

The ranges below are commonly supplied. Exact availability depends on alloy, temper, and process, and is confirmed against your drawing.

Shape Typical size range Standard length
Round bar Diameter 6–300 mm 1–6 m
Flat bar Width 10–600 mm × Thickness 3–150 mm 1–6 m
Square bar Side 6–200 mm 1–6 m
Hex bar Across flats 8–100 mm 1–6 m
Rectangular bar Width × Thickness per request (comparable to flat-bar envelope) 1–6 m

 

Standard and Custom Aluminum Bar Lengths

Standard lengths are 1–6 m. Cut-to-length pieces are supplied to your required dimension, and non-standard cross-sections can be produced to drawing.

 

Dimensional Tolerances for Aluminum Bars

Dimensional tolerances follow ASTM B211 (cold-finished bar) or ASTM B221 (extruded bar, rod, and shapes) and are confirmed against your drawing. Tolerances are size- and process-dependent — a single tolerance value should not be applied across all alloys and sections. Straightness is typically held to a small per-metre deviation; tighter tolerances are available on request.

Request a size confirmation

 

Aluminum Bar Manufacturing and Sourcing Capabilities

In-House Aluminum Bar Production Capabilities

GNEE supplies aluminum bars through a combination of in-house processing and qualified sourcing. The exact split depends on the alloy, shape, temper, and quantity of each order, and we state which route applies when we quote.

 

Additional Sourcing for Aluminum Bar Requirements

Where a specification is outside our in-house process envelope, we fulfill it through partner production or external procurement that meets the same material and documentation requirements. This lets us cover a wider alloy and size range without implying that every item is made on our own lines.

 

Aluminum Bar Production and Order Verification

Every order goes through a verification step: we confirm alloy, temper, dimensions, standard, quantity, inspection level, and delivery date before production or purchase. Quality documents and acceptance criteria are agreed up front, and differ by supply route.

 

Aluminum Bar Manufacturing

 

Discuss your aluminum bar requirements

Aluminum Bar Standards and Quality Control

Applicable Aluminum Bar Product Standards

We work to the product standards that match the manufacturing process: ASTM B211 for cold-finished aluminum bar, and ASTM B221 for extruded aluminum bar, rod, and shapes. Listing a standard means the product is produced and inspected to that standard.

 

Chemical and Mechanical Testing for Aluminum Bars

Depending on the order, we perform or arrange alloy verification (XRF / PMI), tensile testing (per ASTM B557), hardness checks, and dimensional inspection. Which tests are included is confirmed on the quote and the inspection level you request.

 

Dimensional Inspection and Aluminum Bar Traceability

Each lot is marked for alloy, temper, size, and heat/lot number so it can be traced back to its Mill Test Certificate. Marking and documentation are agreed per order.

 

Material Test Certificates for Aluminum Bars

Every shipment includes a Mill Test Certificate to EN 10204 3.1. EN 10204 3.2 and third-party inspection by SGS, BV, or TÜV can be arranged on request.

Confirm inspection requirements

Export compliance note. Some high-strength 7xxx-series alloys supplied as cylindrical solid round bar (for example 7075-T6, with ultimate tensile strength at or above 460 MPa) may be subject to China dual-use export control. Flat, square, hex, and rectangular bars, and other forms, are not in the controlled shape category. For any high-strength solid round bar, we confirm export eligibility per order and can offer 5xxx / 6xxx alternatives (5083-H116, 6082-T6, 6061-T6) where suitable.

 

Applications of Aluminum Bars

Aluminum Bars for CNC Machining and Precision Components

Round, square, and hex bars are widely used for turned and milled parts — shafts, bushings, spacers, and fixtures — where aluminum's machinability and weight save cost versus steel. 6061 and 6082 are common choices for general machining.

 

Aluminum Bars for Industrial Equipment and Fixtures

Flat and rectangular bars suit machine guards, base plates, brackets, and jigs. Alloy choice follows the needed strength and any welding: 5052 / 5083 where corrosion resistance matters, 6xxx where weldability and strength are both required.

 

Aluminum Bars for Structural and Transportation Components

Structural members, frames, and vehicle components use 6082-T6 and 6061-T6 for their strength-to-weight and weldability. Where a project specifies marine or welded construction, 5083 is a frequent selection.

 

Custom Aluminum Bar Processing Services

Cut-to-Length Aluminum Bar Service

We cut bars to the length you specify, with square or mitered ends, so material arrives ready for the next operation.

 

Custom Aluminum Bar Dimensions and Drawing Review

Send a drawing or size list and we review alloy, tolerance, and process feasibility before quoting. Non-standard cross-sections and special tolerances are evaluated case by case.

 

Secondary Aluminum Bar Processing

Where confirmed as available, we provide drilling, tapping, milling, and surface treatment (bright drawing, polishing, brushing, anodizing, powder coating) to drawing. We state clearly which steps are done in-house and which through partners.

 

Aluminum Bar Supply for Buyers

Export Packaging and Shipping for Aluminum Bars

We coordinate export packaging — strapped bundles with end protection, moisture-barrier (VCI / PE) wrap, and crating or palletising where needed — plus shipping documents. Exact packaging and Incoterms are confirmed per order.

 

Destination and Documentation for Aluminum Bar Orders

Destination port, trade terms (FOB / CIF), lead time, and transport plan are confirmed against each order. We can arrange documentation for a range of destinations; tell us the port and Incoterm and we will confirm feasibility.

 

Aluminum profile extrusion die stock, showcasing the raw material used for manufacturing dies to shape aluminum profiles during extrusion.

Mold Warehouse

Aluminum profile extrusion workshop showcasing the process of shaping aluminum billets into profiles through an extrusion press.

Extrusion Workshop

Aluminum profile anodizing workshop showcasing the process of applying anodized finishes to aluminum profiles for enhanced durability and aesthetics.

Anodiziing Workshop

Aluminum profile vertical powder coating workshop, showcasing the process of powder coating aluminum profiles in a vertical position for uniform finish.

Vertical Powder Coated

Aluminum profile horizontal powder coating workshop, showcasing the process of applying powder coating to aluminum profiles in a horizontal position for a uniform finish.

Horizontal Powder Coated

Aluminum profile being laser welded, showcasing the seamless, high-precision welding process for aluminum profiles.

Welding Equipment

Aluminum profile warehouse displaying a variety of aluminum profiles stored and organized for manufacturing and distribution.

Warehouse

Aluminum profile CNC machining workshop showcasing various CNC machines used for precision milling, drilling, and shaping of aluminum profiles.

CNC Machining

Aluminum profile punching workshop showcasing the process of punching holes, slots, and custom shapes in aluminum profiles for various applications.

Punching Equipments

 

 

 

 

 

 

 

Why Choose Us for Aluminum Bar Supply

Aluminum Bar Product Range and Order Coordination

GNEE has supplied wrought aluminum products since 2008 and exports to more than 100 countries. We coordinate five bar shapes, multiple alloys and tempers, and both stock and made-to-order quantities through one point of contact.

 

Aluminum Bar Quality Verification

Material is verified by alloy and dimension, and every shipment carries an EN 10204 3.1 Mill Test Certificate. Where a bar is sourced rather than made in-house, it passes the same verification before dispatch.

 

Custom Aluminum Bar Order Support

Our sales engineers read drawings and ask about load, environment, and weld plan before recommending alloy and temper, so the bar you receive matches the job rather than a generic catalogue line.

 

GNEE ALUMINUM

 

6061 t6511 Aluminum Bar MTC
6061 t6511 Aluminum Bar MTC
6061 T6 Aluminum Bar MTC
6061 T6 Aluminum Bar MTC

Request a Quote for Aluminum Bars

Tell us what you already know and we will confirm the rest. To speed up a quote, send:

Shape — round / flat / square / hex / rectangular

Alloy & temper — e.g. 6061-T6, 6082-T6, 7075-T651 (if known)

Dimensions & length — diameter, width × thickness, side, or across-flats; cut length if required

Quantity — pieces, metres, or tonnes

Standard / inspection — ASTM B211 / B221, EN 10204 3.1, third-party if needed

Drawing / spec file — optional, but speeds custom orders

Destination / Incoterm — port and FOB / CIF if known

Commercial terms. MOQ flexible — both small trial orders and large-volume orders (including full containers and long-term contracts) are accepted. Lead time 15–30 days from order confirmation for standard specifications. Every shipment includes an EN 10204 3.1 Mill Test Certificate; 3.2 and third-party inspection (SGS, BV, TÜV) can be arranged. Pricing follows the SMM (Shanghai Metals Market) aluminum ingot price and is quoted per order. We reply within 24 hours.

 

ALUMINUM TEAM

 

FAQ

What aluminum bar shapes can you supply?

We supply five cross-sections: round, flat, square, hex (hexagonal), and rectangular aluminum bar. Each is available across a range of alloys, tempers, and lengths, produced or sourced to your drawing.

 

What aluminum alloys and tempers are available?

Commonly supplied alloys include 1050, 3003, 5052, 5083, 6061, 6063, 6082 and 7075, in tempers from O / Hxxx (non-heat-treatable) to T4 / T5 / T6 / T651 (heat-treatable). Temper changes strength and machinability, so we recommend the alloy-temper pair for your application rather than alloy alone.

 

What sizes and lengths can you provide?

Typical ranges are round 6–300 mm diameter, flat 10–600 mm wide × 3–150 mm thick, square 6–200 mm side, hex 8–100 mm across flats, and rectangular bars to comparable dimensions. Standard lengths run 1–6 m, with cut-to-length available. Exact ranges are confirmed against your drawing.

 

Which standards apply to aluminum bars?

Cold-finished bars follow ASTM B211; extruded bars, rods and shapes follow ASTM B221. Material is supplied with EN 10204 3.1 Mill Test Certificates; 3.2 and third-party inspection (SGS, BV, TÜV) can be arranged on request.

 

Can you supply custom-cut aluminum bars?

Yes. We provide cut-to-length, custom dimensions, and secondary processing (drilling, tapping, milling, surface treatment) against your drawing. Send the drawing or size list and we quote material and processing together.

 

What inspection documents are available?

Every shipment includes an EN 10204 3.1 Mill Test Certificate. EN 10204 3.2 and third-party inspection by SGS, BV, or TÜV can be arranged on request, and the inspection level is agreed on the quote.

 

How can I request a quotation?

Send the shape, alloy and temper, dimensions and length, quantity, target standard, and destination. We confirm the specification and return a written quote with MOQ, price, and lead time, typically within 24 hours.

 

Can you arrange shipment to my destination in Asia or the Middle East?

We coordinate export packaging, shipping, and documentation for a range of destinations. Tell us the port and Incoterm (FOB / CIF) and we confirm feasibility and lead time per order.

Contact us for product-specific details

We're professional aluminum rod manufacturers and suppliers in China, specialized in providing high quality products and service. We warmly welcome you to wholesale discount aluminum rod for sale here from our factory. For price consultation, contact us.

(0/10)

clearall