HENAN GNEE NEW MATERIAL CO., LTD
86-372-5055135

Key Differences in 5083 H116 VS H321 Aluminum Alloy Heat Treatment Processes

Nov 13, 2025

Key Differences in Heat Treatment Processes

Process Parameter H116 H321 Practical Significance
Cold Working Deformation 12–18% 25–35% H321 requires higher rolling pressure and equipment capacity
Stabilization Temperature 150–200°C 120–170°C H321 uses a lower temperature but a longer stabilization duration
Processing Time 1–2 hours 3–6 hours H321's production cycle is about 50% longer
Intergranular Corrosion Testing ASTM G67 ASTM G67 Both must meet the same testing standard
Final Hardness Grade Quarter Hard Half Hard H321 is harder but still suitable for cold bending

Expert Tip:
Although H321 undergoes an additional stabilization treatment, its "half-hard" hardness is mainly derived from the greater degree of cold work deformation-not from heat treatment itself. This is fundamentally different from heat-treated alloys like 6061-T6.

 

Chemical Composition Comparison: Do H116 and H321 Share the Same Alloy Formula?

A common misconception is that 5083 H116 and H321 have different compositions. In fact, they are chemically identical-the difference lies entirely in the temper treatment, not the alloy formulation. According to ASTM B209, both must comply with the following composition limits:

Element Content Range Function
Magnesium (Mg) 4.0–4.9% Main strengthening element; provides solid solution strengthening and protective oxide layer
Manganese (Mn) 0.4–1.0% Refines grains, raises recrystallization temperature, and enhances corrosion resistance
Chromium (Cr) 0.05–0.25% Prevents recrystallization, stabilizes grain structure, and reduces stress corrosion cracking
Iron (Fe) ≤0.40% Impurity must be controlled to ensure corrosion resistance
Silicon (Si) ≤0.40% Minor impurity; improves casting fluidity
Copper (Cu) ≤0.10% Limited strictly to prevent galvanic corrosion
Zinc (Zn) ≤0.25% Impurity element
Titanium (Ti) ≤0.15% Acts as a grain refiner
Aluminum (Al) Balance (92.4–95.6%) Base element

Data Source: ASTM B209 Standard Specification

Important Note:
Although both grades share the same chemical composition, small batch-to-batch variations within the standard range are normal. Reliable suppliers like GNEE, a Chinese aluminum supplier, provide a Mill Test Certificate (MTC) with the exact composition for each batch rather than simply stating standard compliance.

5083 H116 VS H321 Aluminum Alloy: Complete Comparison Guide for Marine & Industrial Applications 2025

Impact of Alloying Elements on Performance

The Mg–Mn–Cr "Golden Combination" Mechanism:

Magnesium (≈4.5%): Creates a solid solution that boosts tensile strength-each 1% increase in Mg raises strength by about 35 MPa. However, exceeding 5% leads to excessive β-phase (Mg₂Al₃) formation during welding, increasing intergranular corrosion risk.

Manganese (≈0.7%): Forms Al₆Mn precipitates that block dislocation motion and enhance strength. Manganese also raises the recrystallization temperature, ensuring fine grains in the weld heat-affected zone for better weld quality.

Chromium (≈0.15%): Works synergistically with Mn to suppress recrystallization and forms chromium-rich barriers along grain boundaries, improving resistance to chloride ion attack.

Case Study:
A shipyard once experienced severe cracking in welded "5083" plates. Testing revealed magnesium content at 5.2%, above the standard limit, causing excessive β-phase precipitation. This case illustrates how even small deviations can have serious consequences. Hence, choosing a certified supplier like GNEE, with ISO 9001 and classification society certifications, is crucial for reliability.

 

Mechanical Properties Comparison: H116 vs. H321

Although both tempers have very similar mechanical performance, ASTM B209 provides the following comparison:

Property 5083 H116 5083 H321 Difference
Tensile Strength (UTS) 317 MPa (46,000 psi) 317 MPa (46,000 psi) Identical minimum
Yield Strength 228 MPa (33,000 psi) 228 MPa (33,000 psi) Identical minimum
Elongation 16% 16% Identical
Shear Strength 190 MPa 200 MPa H321 about 5% higher

Interpretation:
Although both grades meet the same minimum standards, H321, with higher cold deformation (half-hard), can exhibit 3–5% higher actual tensile strength. However, for structural design, they are considered interchangeable since design values are based on standard minimums.

 

Hardness and Fatigue Performance

Performance Parameter H116 H321 Test Standard
Brinell Hardness (HB) 85 85 ASTM E10 (500kg load, 10mm ball)
Fatigue Strength (10⁷ cycles) 159 MPa 159 MPa Rotating beam test
Modulus of Elasticity 70.3 GPa 70.3 GPa ASTM standard
Poisson's Ratio 0.33 0.33 Identical

Practical Impact:
Because H116 is slightly softer, it allows tighter bends-recommended bend radius R = 2t (t = thickness), compared to R = 2.5t for H321. For projects involving complex bending, H116 reduces cracking and scrap rates.

Engineering Case:
A yacht builder initially used H321 for 6 mm hull plates but saw a 3% crack rejection rate during bending. After switching to H116, the rejection rate dropped to 0.5%. Increasing plate thickness to 6.5mm fully compensated for the strength difference, lowering total costs by 8%.

 

Elastic Modulus and Physical Properties

Physical parameters remain essentially identical for both tempers because they depend on atomic structure rather than tempering:

Modulus of Elasticity (E): 70.3 GPa

Density (ρ): 2.66 g/cm³

Poisson's Ratio (ν): 0.33

Design Significance:
When performing FEA or other structural analyses, H116 and H321 can share identical material property inputs, simplifying the design process.

 

Corrosion Resistance: Is H321 Significantly Better?

Corrosion performance is the main distinction between H116 and H321, explaining the slight cost difference. Overall, H321 offers around 5–12% better corrosion resistance, which in marine environments can translate into an additional 5–10 years of service life.

H116 Corrosion Performance

Tests Passed:

ASTM G67 (NAMLT): <15 mg/cm² mass loss

ASTM G66: 7-day immersion test, no signs of intergranular corrosion

ASTM B928: Marine-grade corrosion resistance requirement

H116 typically exhibits a corrosion rate of 0.5–1.0 μm/year in marine atmospheres-meaning it would take 50–100 years for 1 mm of material to corrode.

H321 Corrosion Performance

H321's enhanced corrosion resistance results from its stabilization treatment, which:

Refines β-phase distribution, reducing intergranular corrosion risk.

Passivates grain boundaries, forming a denser oxide barrier.

Relieves residual stress, minimizing susceptibility to stress corrosion cracking.

In static seawater (20°C), H116 corrodes at ≈2.5 μm/year, while H321 corrodes at ≈2.2 μm/year, an improvement of about 12%.

5083 H116 VS H321 Aluminum Alloy

In Summary:
Both 5083 H116 and H321 aluminum plates-supplied by GNEE, a Chinese manufacturer and exporter-offer outstanding strength, weldability, and marine corrosion resistance. H321 provides slightly enhanced protection for long-term exposure, while H116 offers better forming performance and cost efficiency. The choice depends on specific project requirements such as design complexity, service life expectations, and fabrication method.