Perforated aluminium plate is specified for facades, ceilings, stair balustrades and acoustic linings because it combines a light module weight with a decorative surface that can be tuned in open area, aperture size and pattern. Cost and buildability are decided early, at the moment the perforation rate and plate module are fixed, because both parameters drive tooling, flatness control and the support structure behind the panel.
What Drives the Cost of a Perforated Aluminium Plate
Three variables dominate the quotation: alloy and temper, plate thickness, and hole pattern complexity. Higher-purity or more heavily alloyed tempers cost more than commodity sheet because of mill price and availability; thicker plate costs more per square metre and also raises panel weight and support demand; complex or densely packed patterns cost more because of punching time, tool wear and scrap rate.
Base material: sheet and plate supplied to ASTM B209 or GB/T 3880 conditions, with temper selected for forming and flatness.
Tooling: dedicated combination punches for repeated patterns versus programmed paths for one-off designs.
Open area and scrap: every additional percentage point of perforation rate raises the volume of removed material and the risk of distortion.
Finishing: anodising, powder coating or PVDF liquid coating adds a per-square-metre step and influences edge quality.
Installation interfaces: frames, reinforcement ribs and edge returns are project-specific and must be priced separately.
As an indicative order of magnitude, a complete facade build-up using metal perforated aluminium panels falls in the region of 800-1000 RMB per square metre, but the figure moves with pattern density, panel size and finish, so it should always be confirmed against a specific drawing set rather than used as a planning constant.
Perforation Methods and Tooling Choice
The punching route determines both achievable geometry and unit cost, and it should follow order volume.
CNC punching with combination tools is the standard route for large quantities and repeated patterns, giving the best cost per hole and consistent hole quality.
Stamping suits very high volumes of a fixed pattern where a dedicated die can be amortised.
Laser perforation handles customised patterns, mixed hole sizes and unique shapes without dedicated tooling, at a higher cost per hole.
Water jet cutting avoids a heat-affected zone and is used where edge metallurgy or burr control matters.
Millimetre-precision machines and modern nesting software allow an unlimited variety of folding and perforated panel designs, including graduation, rotation and mixed-density patterns across a single elevation.
Perforation Rate, Aperture and Visual Performance
Perforation rate is the percentage of the perforated zone occupied by holes. It is the core factor controlling the unit appearance of a facade, the amount of solar radiation transmitted, and the resulting cooling energy demand. It also controls how difficult the panel is to keep flat.
| Parameter | Typical practice | Effect on the project |
|---|---|---|
| Perforation rate | Up to about 60% with current machinery | Higher open area transmits more daylight and heat but reduces flatness |
| Panel module | Within roughly 1500 × 3000 mm | Larger panels need secondary positioning and re-clamping during punching |
| Aperture and pitch | 6 mm holes on 15 mm centres is the most common combination | Controls visual clarity of the perforated surface and shading coefficient |
| Plate thickness | Selected against wind load and span | Thicker plate resists distortion but adds weight and cost |
| Flatness inspection | Acceptance limits relaxed relative to solid plate | High open area panels cannot meet the flatness tolerances of unperforated sheet |
Controlling aperture, hole spacing and arrangement changes the visual clarity of the perforated surface and creates different shading effects. Combining perforation rate with plate thickness allows the designer to cut solar radiation heat gain while keeping the required daylight level.
Structural Fixing: Keel Systems and Panel Connections
A perforated plate is thin and its own stiffness is not sufficient to span between the main structural connectors of a building, so the standard build-up is a three-part system: main structure, keel or supporting frame, then the metal perforated plate. The keel carries wind load and transfers it back to the primary frame, and its spacing is set by the panel module and the plate thickness.
The plate-to-structure connection is normally discontinuous and indirect, using bolts or rivets, because a resilient skin is easier to disassemble, maintain and replace at the end of service. Continuous methods such as welding and bonding are used where a monolithic appearance is required, but they complicate future renewal and demand tighter process control. Connection detailing also depends on the metal and finish: anodised and coated surfaces should be fastened through isolated or protected interfaces to avoid damaging the finish and to prevent galvanic contact with steel supports.
Specification Checklist for Facade and Interior Projects
Fix the aperture, pitch and arrangement first, since these set visual clarity and shading performance.
Choose the plate type and module next, because strength determines panel size and keel spacing.
Match alloy and thickness to the exposure: heavier gauges for high wind-load elevations, lighter gauges for ceilings and interior linings.
Decide whether the panel needs a frame, a folded edge return or reinforcement ribs for the specific span.
Confirm the acoustic intent where the panel works as a sound-absorbing lining behind which porous absorber is placed.
Agree the flatness acceptance criteria with the perforation rate in view, before production starts.
Frequently Asked Questions
Q: What is the maximum perforation rate available?
With current punching equipment the open area can reach about 60%, but the practical limit for a given project is usually set by flatness requirements rather than by the machine.
Q: Why is 6 mm aperture on 15 mm spacing so common?
That combination gives a balanced open area with good visual clarity and predictable shading, and it works with standard combination tooling, which keeps unit cost low.
Q: Can large perforated panels be produced in one piece?
Panels are normally kept within roughly 1500 × 3000 mm; beyond that range the sheet needs secondary positioning and re-clamping during punching, which raises cost and increases dimensional variation.
Q: Which perforation method is best for a custom pattern?
Laser perforation handles custom patterns, mixed hole sizes and unique shapes without dedicated tooling, while CNC combination punching remains cheaper for large volumes of a repeated pattern.
Q: Why is a keel system required behind the panel?
A thin perforated plate cannot carry wind load by itself, so a keel or supporting frame spans between main structure connectors and provides the fixing points for the skin.
Q: Are welded connections recommended for perforated facades?
Bolted or riveted discontinuous connections are preferred because they allow disassembly, maintenance and replacement; welding and bonding are reserved for projects that need a continuous, monolithic appearance.







