Overview of 5083 0.5mm Marine Grade Plate and Sheet
5083 is an Al-Mg alloy from the 5xxx series and is the standard choice for marine and coastal work because of its resistance to seawater corrosion and stress-corrosion cracking. At 0.5 mm thickness it serves thin-gauge applications where weight reduction, flexibility and corrosion performance matter more than stiffness: small craft hull panels, trim, decking, interior linings and lightweight cladding.
The material is supplied in the O, H111 and H32 tempers, in coils for continuous forming or as cut-to-length sheets. It conforms to ASTM B209 for sheet and plate, EN 485 and EN 573 for European requirements, and ISO 6361, with a mill test certificate available to EN 10204 3.1 or 2.2.
Key features include outstanding resistance to seawater and marine atmospheres, high tensile strength with good toughness even at sub-zero temperatures, good weldability with MIG and TIG processes, excellent formability at thin gauge, and a low density of about 2.66 g/cm3.
Chemical Composition
| Element | Typical Range (%) |
|---|---|
| Magnesium (Mg) | 4.0 - 4.9 |
| Manganese (Mn) | 0.4 - 1.0 |
| Chromium (Cr) | 0.05 - 0.25 |
| Iron (Fe) | 0.5 max |
| Silicon (Si) | 0.4 max |
| Copper (Cu) | 0.1 max |
| Zinc (Zn) | 0.25 max |
| Titanium (Ti) | 0.15 max |
| Others, each / total | 0.05 max / 0.15 max |
| Aluminum (Al) | Balance |
Magnesium supplies the solid-solution strengthening and the corrosion resistance, while manganese and chromium refine the grain structure and improve resistance to pitting and stress-corrosion cracking. Certified composition for the delivered lot is stated on the mill test certificate.
Mechanical Properties at 0.5 mm
| Property | O | H111 | H32 |
|---|---|---|---|
| Tensile strength, Rm (MPa) | 195 - 250 | 270 - 320 | 300 - 340 |
| Yield strength, Rp0.2 (MPa) | 35 - 60 | 130 - 170 | 160 - 210 |
| Elongation, A (%) | 12 - 22 | 6 - 12 | 4 - 10 |
| Hardness | About 30 - 40 HB | About 50 - 70 HB | About 60 - 80 HB |
| Density (g/cm3) | 2.66 | 2.66 | 2.66 |
| Low-temperature toughness | Excellent | Very good | Good |
The O temper is fully annealed and gives maximum formability with the lowest strength, H111 is strain hardened for a balance of strength and ductility in thin sheet, and H32 is strain hardened and stabilized for higher strength with reduced elongation. Selection follows the forming severity of the part and the load it must carry.
Formats, Tolerances and Surface Finishes
Thickness: 0.5 mm, normally within plus or minus 0.03 mm or to customer specification
Widths: 1000 mm, 1250 mm, 1500 mm or cut to size, with width tolerance of plus or minus 1.0 to 5.0 mm
Length: coils for continuous forming, or cut-to-length sheets within plus or minus 2 to 5 mm
Edge: mill edge, slit edge or custom trimmed
Finishes: mill finish with light rolling marks, bright annealed, pre-painted with PVDF or FEVE coatings, anodized, or lacquered
Protection: protective film for scratch resistance, packed in wooden crates with seaworthy export packing
Documentation: mill test certificate to EN 10204 3.1 or 2.2, with dimensional and mechanical records
Fabrication, Welding and Corrosion Protection
Welding is performed with MIG or TIG using 5356 filler, with correct technique to avoid hot cracking at thin gauge. Forming supports tight bend radii, and the O temper allows the greatest flexibility for profiling and compound shaping. Cutting can be done by laser, shearing, waterjet or plasma, and surfaces should be degreased before painting, coating or adhesive bonding. Anodizing is possible after suitable pre-treatment.
Resists seawater immersion, salt spray and coastal atmospheres
Magnesium and chromium content limits pitting and stress-corrosion cracking
Avoid prolonged contact with copper and copper alloys
Use insulating layers or protective coatings between dissimilar metals
Maintain coatings in high-chloride environments as part of routine service
Store flat, dry and off the ground, keeping protective film in place until final fabrication
At sub-zero temperatures the alloy keeps its toughness and mechanical performance, which makes it suitable for cold-climate marine work and cryogenic service where the temperature range has been verified for the specific application.
Frequently Asked Questions
Q: Why choose 5083 rather than 5052 for marine use?
5083 contains more magnesium and manganese, giving it higher strength and better resistance to stress-corrosion cracking in seawater. It is preferred for hulls and structural marine parts, while 5052 remains a good general-purpose marine alloy.
Q: Which tempers are available at 0.5 mm?
O, H111 and H32 are the standard options. O gives the highest ductility, H111 a mid-range balance, and H32 the highest strength of the three at the cost of some elongation.
Q: Can 0.5 mm sheet be welded?
Yes, with MIG or TIG and 5356 filler. Thin gauge demands low heat input, careful fit-up and clean edges to prevent burn-through and hot cracking.
Q: Which standards apply?
ASTM B209 covers sheet and plate requirements, EN 485 covers mechanical and dimensional properties, EN 573 covers composition, and ISO 6361 covers wrought sheet, strip and plate.
Q: How is the sheet protected during shipping?
Protective film is applied to the surface, and coils or sheets are packed in wooden crates with seaworthy export packing to prevent moisture ingress and mechanical damage in transit.
Q: Is the material suitable for low temperatures?
Yes. The alloy retains toughness and strength at sub-zero temperatures, which is one reason it is specified for cryogenic containers and cold-climate marine structures.







