If you are sourcing 1100-H19 aluminum sheet for electronics, heat-transfer parts, nameplates, lighting components or decorative panels, the first number most buyers ask for is the 1100-H19 aluminum sheet price per ton. There is no single fixed number. A workable quotation is built from a published base aluminum price plus the conversion, slitting, finishing, inspection and packing work needed for your specification. This article explains how that number is assembled, gives a weight-based reference you can check yourself, and lists what to send a supplier to get a usable quote.
Indicative reference basis (SMM-based, not a firm quote)
Base metal element + processing element, confirmed against the current SMM quote on the order date
SMM A00 aluminum, November 3, 2026: 23,450 CNY/mt (≈ ¥23.45/kg; ≈ $3,126.84/ton VAT-excluded, or ≈ $3,533.33/ton VAT-included), converted at USD/CNY 6.6368. This is the raw base-metal benchmark, not a 1100-H19 aluminum sheet price. It is the latest figure published in our perforated aluminum sheet price reference guide; confirm it against a live SMM quote before budgeting, because the metal element moves with the market.
For a firm 1100-H19 aluminum sheet quote, send the alloy and temper, thickness, width and length (or coil inner/outer diameter), surface finish, quantity, inspection requirement and destination port. Request a quote with your specification.
Current 1100-H19 Aluminum Sheet Price Benchmark
The reliable way to read any aluminum sheet price is to separate the metal from the work done to it. The metal element tracks a published daily benchmark; the processing element is quoted against your drawing, temper and order size. A quotation that mixes the two without showing the split gives you no way to compare two suppliers or to re-check the number a week later.
Base aluminum price benchmarked to SMM for 1100-H19 sheet
GNEE quotes the metal element benchmarked to SMM (Shanghai Metals Market). The November 3, 2026 A00 figure of 23,450 CNY/mt is the starting point for calculating the metal content of a sheet, not a price list for 1100-H19 aluminum sheet itself. 1100 is a commercially pure 1xxx-series alloy (Al 99.00% min), so its metal element sits close to the primary aluminum benchmark; the full-hard H19 condition adds rolling work, and that work is priced separately. Because the base element changes daily, the quotation is confirmed close to the order date.
The figures in this article are market references for estimating, not a GNEE quotation. The SMM number above is dated November 3, 2026; the USD conversion uses USD/CNY 6.6368 from the same date. Processing, packaging, freight and trade terms are not included in the metal element. The only firm 1100-H19 aluminum sheet price is the one returned after your specification is reviewed.
1100-H19 Aluminum Sheet Pricing
| Pricing element | What determines it | How it is quoted |
|---|---|---|
| Base aluminum element | SMM A00 daily benchmark × sheet weight | Recalculated on the order date |
| Alloy and temper conversion | 1100 purity control, cold rolling to H19 full hard, thickness reduction | Per thickness and width |
| Slitting and cut-to-length | Number of cuts, width tolerance, edge condition | Per order drawing |
| Surface finish | Mill finish standard; anodized, brushed or coated options | Per finish and film specification |
| Inspection documents | EN 10204 3.1 MTC standard; 3.2 or third-party inspection on request | Confirmed against the contract |
| Packing, freight and terms | Export pallet or crate, destination, FOB or CIF | Per shipment and destination |
Three points are worth stating plainly. H19 is a full-hard temper reached by cold rolling, so thin gauges and tight width tolerances carry more conversion work than annealed sheet - ask for the achievable H19 thickness and width before you fix your design. An export quote also has to name the trade term: FOB and CIF prices for the same sheet are not comparable. And a request for 3.2 certification or witnessed inspection should be in the first inquiry, because it is arranged before production, not added after the coil is rolled.
1100-H19 Aluminum Sheet Price Reference by Thickness and Weight
Both the metal cost and most freight are weight-based, so start from weight rather than comparing a price per sheet alone. For 1100 aluminum the density is 2.71 g/cm³, which gives weight per m² (kg) = thickness (mm) × 2.71. The table below applies that to a 1000 × 2000 mm sheet (2 m²) and values the metal content at the November 3 SMM benchmark of 23.45 CNY/kg (≈ $3.53/kg).
| Thickness (mm) | Weight (kg/m²) | Weight per 1000 × 2000 mm sheet (kg) | Base metal value per sheet (CNY) | Base metal value per sheet (USD) |
|---|---|---|---|---|
| 0.5 | 1.355 | 2.710 | 63.55 | 9.58 |
| 0.8 | 2.168 | 4.336 | 101.68 | 15.32 |
| 1.0 | 2.710 | 5.420 | 127.10 | 19.15 |
| 1.5 | 4.065 | 8.130 | 190.65 | 28.73 |
| 2.0 | 5.420 | 10.840 | 254.20 | 38.30 |
Weight-based cost example for 1100-H19 aluminum sheet
Take a 1.0 mm × 1000 × 2000 mm sheet in 1100-H19, mill finish. Its weight is 2.71 kg/m² × 2 m² = 5.42 kg. At the November 3 SMM benchmark of 23.45 CNY/kg the metal content is about 127 CNY (≈ $19.15). That is the metal element only. The processing element for full-hard rolling, slitting, cutting, leveling and packing is quoted separately against the order, and the final FOB or CIF figure may also include inspection, packaging and freight. This arithmetic is illustrative; it is not a GNEE quotation. A buyer comparing a 1100 aluminum sheet price per kg, per square meter or per ton should first check that all three are being quoted on the same basis (metal only, or metal plus processing, and at which trade term).
Thickness values above are an indicative thin-gauge range for a full-hard condition. H19 is supplied on specification within GNEE's published 1100 aluminum range; confirm the achievable H19 thickness, width and temper for your order before using the table. Density and the SMM benchmark are reference data; the mill test certificate governs the delivered lot.
What to Specify for a 1100-H19 Aluminum Sheet Quotation
A supplier cannot price "1100 H19 sheet" without the specification. Send these items in the first message and you will normally get one round of quoting instead of three:
Alloy and temper: 1100-H19, with the applicable standard (ASTM B209 / ASME SB209 for flat-rolled aluminum sheet).
Thickness, width and length - or coil form with inner/outer diameter if you buy 1100-H19 aluminum coil or strip.
Surface finish: mill, brushed, anodized, coated, and any film or protective interleaving requirement.
Quantity, and whether the order is a small trial order, a full-container order or a long-term contract volume.
Inspection documents: EN 10204 3.1 MTC, or 3.2 / third-party inspection if your project requires it.
Trade term and destination: FOB or CIF, port of discharge, and payment terms (T/T or L/C).
Cut-to-size or drawing-based work, edge condition, and dimensional tolerance.
If you are checking stock before a bulk order, ask explicitly about 1100-H19 aluminum sheet in stock and the ex-stock thickness range; base sheet availability can shorten the delivery window, while a specific full-hard temper is confirmed case by case.
Commercial Terms for 1100-H19 Aluminum Sheet Orders
GNEE works on the following commercial terms for 1100-H19 aluminum sheet orders:
MOQ flexible - both small trial orders and large-volume orders accepted. Full-container and long-term contract orders are welcome; larger volumes usually receive better terms. Confirm the workable minimum against your thickness, temper and finish.
Lead time 15–30 days, confirmed against alloy availability, thickness, temper, finish and order volume.
EN 10204 3.1 mill test certificate accompanies each order, covering alloy, temper, composition and mechanical properties; 3.2 and third-party inspection can be arranged where the contract requires it.
Pricing benchmarked to SMM; the metal element is confirmed against the SMM quote on the order date, with FOB / CIF and T/T / L/C available.
Inquiries answered within 24 hours, including a specification check and a project-specific quotation.
GNEE as a 1100-H19 Aluminum Sheet Supplier
GNEE supplies 1100 aluminum sheet, strip and coil to international distributors, equipment manufacturers and project buyers. As a 1100-H19 aluminum sheet manufacturer and exporter, we handle cut-to-length sheets, slit strip, drawing-based sizing and surface finishing, with dimensional and visual inspection before packing. The H19 full-hard condition is supplied on specification within the published 1100 range; O, H14 and H18 are the standard-listed tempers. Typical uses for 1100-H19 aluminum sheet include nameplates, lighting and reflector parts, heat-transfer components, electronic parts and decorative panels where high purity, conductivity and the stiffness of a full-hard sheet are needed.
Export packing is arranged per order - protective film or interleaving, strapping, pallet or wooden crate - together with the inspection documentation and logistics coordination. Our Singapore project news documents a Southeast Asian shipment of perforated aluminum panels; ask for a project reference matching your alloy and destination when you inquire.
About GNEE
Established in 2008, exporting aluminum products to 100+ countries and regions.
Sheet, plate, coil, strip, foil, bar, tube, profile and fabricated aluminum products from one source.
Flexible MOQ for both small and large orders, with a typical 15–30 day lead time.
Per-order cutting, slitting and finishing, EN 10204 3.1 mill test certificates, and export-grade packing.
Quotations benchmarked to SMM, with FOB / CIF terms, T/T or L/C payment, and a 24-hour inquiry response.
Request a Quote for 1100-H19 Aluminum Sheet
Send your thickness, width, quantity, finish and destination to get a current 1100-H19 aluminum sheet quotation or check availability and lead time. Buyers searching for a 1100-H19 aluminum sheet supplier in the UAE, Saudi Arabia, Vietnam, Singapore or Malaysia can request a destination-specific FOB or CIF quote in the same message.
Learn more about 1100 H19 aluminum sheet case studies
FAQ
How much does 1100-H19 aluminum sheet cost per ton?
There is no single per-ton figure for finished sheet. The metal element starts from the SMM A00 benchmark (23,450 CNY/mt on November 3, 2026), and the conversion, slitting, finishing, inspection and packing elements are added per specification. Ask for a quotation that shows the metal element separately, then confirm it against the SMM quote on the order date.
What is the MOQ for 1100-H19 aluminum sheet?
MOQ is flexible - both small trial orders and large-volume orders are accepted, including full-container and long-term contract orders. Confirm the workable minimum for your required H19 thickness and width, since a specific full-hard temper is scheduled against production availability.
How is 1100-H19 aluminum sheet priced?
Price = base aluminum element (SMM benchmark × sheet weight) + processing element (rolling to H19, slitting, cutting, finishing) + inspection, packing, freight and the chosen trade term. Weight comes from thickness × 2.71 g/cm³ × area, so a price per kg, per square meter and per ton can all be reconciled to the same sheet.
How long does 1100-H19 aluminum sheet delivery take?
Typical lead time is 15–30 days, confirmed against alloy availability, thickness, temper, finish and order volume. Ex-stock base sheet can shorten the window; a specific H19 temper or custom width is confirmed case by case.
Can I buy 1100-H19 aluminum sheet cut to size?
Yes. Cut-to-length sheets, slit strip and drawing-based sizing are available. Include the finished dimensions, edge condition and tolerance in your inquiry, and ask for the achievable H19 thickness and width. An EN 10204 3.1 mill test certificate is supplied with the order.
