HENAN GNEE NEW MATERIAL CO., LTD
86-372-5055135

Standard Width of Aluminum Corrugated Sheet: Model-by-Model Guide

May 30, 2025

The Standard Width Range for Aluminum Corrugated Sheet

Aluminum corrugated sheet is produced by roll forming aluminium or aluminium alloy coil into a repeating wave profile. Because the profile itself consumes part of the strip width, two values always have to be distinguished: the feeding width of the coil and the effective coverage width of the finished panel. The effective figure is the one that matters on site, since the overlap removed during fixing is deducted from it.

In commercial production the common feeding width band is 750-1500 mm. The exact value is governed by the corrugation model, the corrugation height and the intended application rather than by a single universal number.

Traditional building enclosure: feeding widths of about 1000-1500 mm dominate.

Aluminium-magnesium-manganese alloy corrugated sheet: 400 mm, 500 mm, 840 mm and 1000 mm are the standard widths.

Curtain wall and decorative cladding: 1000-1500 mm, including the common width of patterned aluminium sheet.

Model 840 sheet, used for exterior wall decoration with aluminium profiles, is produced at 840 mm.

Typical Widths by Corrugation Model

The table below summarises the width values most frequently ordered against each corrugation family, together with their usual field of use.

Corrugation model Standard width (mm) Application scenario
Wave 20-106 1115 Traditional enclosure structure
Wave 33-131 1008 Strengthened compression engineering
YX35-125-750 750 (effective coverage) Large-span roof and curtain wall
Model 840 840 Exterior wall decoration
Fine wave decorative profile 400-1000 Interior and façade cladding

The base coil for these profiles is normally ordered to GB/T 3880.1 or EN 485-2 in alloys such as 3003, 3004, 3105 and 5052, with the temper chosen to suit the bending radius of the profile. Dimensional and flatness tolerances come from the coil standard, while the formed profile is checked against the requirements of GB/T 12755 for cold-formed profiled sheet.

Why Effective Coverage Is Narrower Than the Coil

A corrugated panel is fixed to the purlin or the framing with a side lap. The lapped zone, typically 10-20 mm per side depending on the fastening system, is covered by the adjacent panel and cannot be counted as weather-exposed area. For example, wave 20-106 sheet is supplied at 1115 mm, but the effective coverage is smaller because the overlap is deducted. Planners who quote roof area directly from the coil width will therefore overstate the covered surface and under-order material.

The width to use in a covering calculation is:

Effective coverage width = supplied width - number of side laps x lap allowance.

Number of panels per run = total run width / effective coverage width, rounded up to a whole panel.

Total order area = effective width x panel length x panel count.

Custom Widths and Their Limits

Standard production allows width customisation, but the freedom is bounded by the roll forming mill and by transport and handling.

Increasing the width beyond about 2000 mm may attract additional cost because the mill stand, shaft length and levelling equipment have to handle the wider coil.

Curtain wall aluminium panels are usually held to 800-1500 mm, taking into account shipping, crane capacity and the convenience of installation at height.

Narrow widths below the standard range are normally obtained by slitting the coil first; slitting quality then determines whether the profile forms without edge cracking.

Length-to-Width Ratio and Cutting Losses

Panel geometry affects material yield as much as the corrugation model does. A length-to-width ratio of about 2:1, for example 600 mm x 1200 mm or 900 mm x 1800 mm, is recommended because it reduces cutting losses and makes the panel easier to handle and nest on the roof.

Two further points should be combined with the width choice:

Corrugation height and wave spacing must be checked together with the width, since they determine the section modulus and therefore the spanning capability.

Mechanical performance requirements, including load class and deflection limits, may force a wider, deeper profile even where a narrower sheet would fit the geometry.

Ordering Checklist

State feeding width and effective coverage width separately.

State the corrugation model code, for example YX35-125-750, rather than a descriptive name.

State alloy and temper.

State the lap allowance so the effective width can be confirmed.

Confirm the maximum width the forming line, transport and site lifting equipment can accept.

Frequently Asked Questions

Q: What is the general standard width range of aluminium corrugated sheet?
The conventional band is 750-1500 mm feeding width, with the specific value driven by the corrugation model and the end use; decorative and cladding grades are usually at the upper end of that band.

Q: What width is the 840 corrugated sheet made in?
Model 840 is produced at 840 mm and is typically used for exterior wall decoration in combination with aluminium profiles.

Q: Why is the effective coverage narrower than the sheet width?
Because each panel laps over the next one by roughly 10-20 mm, and the lapped portion is not exposed covering area. The overlap allowance must be deducted before the coverage is calculated.

Q: Can widths above 1500 mm be produced?
Yes, custom widths are possible, but values above about 2000 mm generally require additional cost because they are limited by the rolling mill and by transport and handling constraints.

Q: Which width and length combination minimises cutting loss?
A length-to-width ratio near 2:1, such as 600 mm x 1200 mm, gives the best compromise between cutting efficiency and easy handling, and it reduces offcut waste on typical roof layouts.

Q: Does the corrugation height change the standard width?
Corrugation height and wave spacing affect the section performance and the forming behaviour rather than the standard width itself, but they must be selected together with the width to reach the required spanning capability.