HENAN GNEE NEW MATERIAL CO., LTD
86-372-5055135

Manufacturing Considerations for 7075 Aluminum

Dec 26, 2025

Export Control Compliance Notice - High-Strength Aluminum Alloys

Certain high-strength aluminum alloy products supplied by GNEE are subject to the export control regulations of the People's Republic of China for dual-use items and technologies. Under these regulations, the export, re-export, or transfer of such items generally requires an export license issued by the competent Chinese authorities. Unlicensed export of the controlled item categories is prohibited.

The alloys listed in the table below represent product categories commonly affected by these controls. Whether a specific inquiry or order is controlled depends on the alloy grade, temper, product form, dimensions, quantity, and intended end-use.

Alloy Grade

Common Temper(s)

Tensile Strength (MPa) - Reference

7075

T6 / T651

540 – 570

7075

T73 / T7351

485 – 500

7075

T76 / T7651

500 – 515

7050

T7451 / T6

475 – 620

2024

T351 / T4

425 – 470

7A04

T6

≥ 530

2014

T6

≈ 460 – 500

2017

T4

≈ 390 – 480 (some specifications may reach higher)

2195

-

≈ 572

7068

-

≈ 623

7055

-

≈ 654

7150

-

≈ 643

GNEE does not export to parties or destinations prohibited under applicable export control and international sanctions laws.

 

Why Manufacturing Considerations Matter

7075 is one of the strongest commercial aluminum alloys, with typical tensile strengths in the 510-570 MPa range in the T6 condition. That strength makes it the material of choice for aerospace structures, defense components, high-load mechanical parts, performance automotive systems, and sporting equipment. However, the same alloying system that produces the strength - high zinc and magnesium with copper - also creates manufacturing constraints. Understanding machinability, weldability, heat-treatment sensitivity, corrosion behavior, formability, and cost before production begins prevents scrap, rework, and premature part failure.

Machinability

7075 has a machinability rating of approximately 70% compared with free-cutting aluminum alloys. It performs well in CNC milling and turning when the setup is rigid and vibration is controlled. Best results are achieved with sharp carbide tools, positive rake angles, and controlled heat input. High-speed machining with coolant is recommended because it prevents work hardening at the cutting edge and extends tool life. The alloy produces stringy chips that can clog tooling, so effective chip evacuation is necessary for consistent surface finish.

Weldability

Conventional fusion welding is not suitable for 7075. The high zinc and magnesium content increases susceptibility to hot cracking, and the heat-affected zone loses a significant portion of its strength. Designers typically use mechanical fastening, adhesive bonding, or riveted joints instead of welded connections. Friction stir welding is technically possible and is used in some aerospace applications, but the process requires specialized equipment and qualified procedures, which makes it costly for general fabrication.

Heat-Treatment Sensitivity

Temper selection strongly influences manufacturing success. T6 provides maximum strength through solution heat treatment followed by artificial aging. T651 adds a controlled stretching step that relieves internal stress, making it ideal for heavy machining operations where dimensional stability matters. Over-aged tempers in the T7x family trade some strength for improved resistance to stress-corrosion cracking. Because strength and corrosion resistance move in opposite directions, the temper must be matched to the service environment as well as the mechanical requirement.

Corrosion Resistance and Protective Finishes

7075 has lower corrosion resistance than alloys such as 6061 or 5052, mainly because its copper content degrades the protective oxide film. In demanding or coastal environments, protective finishes are normally required: hard anodizing, chromate conversion coating, or powder coating, with proper sealing for marine or chemical service. For maximum protection in chloride-rich environments, alclad 7075, which carries a thin high-purity aluminum cladding, is an established alternative.

Formability and Cost

Formability is limited by the alloy's high hardness in heat-treated tempers. Tight bends are discouraged because cracking can occur at the outer fiber; machining is preferred over forming for complex shapes. Cost is the final consideration: 7075 typically costs 25-60% more than 6061 for equivalent forms, and its abrasiveness increases tooling wear and machining cost. The premium is justified when strength-to-weight ratio is mission-critical and failure is not an option.

Typical Mechanical Properties

Published typical values for 7075-T6/T651 include an ultimate tensile strength of about 572 MPa, a tensile yield strength of about 503 MPa, elongation at break of about 11%, a modulus of elasticity of 71.7 GPa, and a Brinell hardness of approximately 150. These figures support design where the part must carry high repeated loads with minimum weight.

FAQ

Q: Can 7075 aluminum be welded?

A: Conventional fusion welding is not recommended because the alloy is prone to hot cracking and loses strength in the heat-affected zone. Mechanical fastening or adhesive bonding is preferred; friction stir welding is possible but costly and requires qualified procedures.

Q: What temper is best for machining 7075?

A: T651 is often preferred for heavy machining because the stress-relieving stretch improves dimensional stability, reducing distortion when large amounts of material are removed.

Q: Why is 7075 less corrosion resistant than 6061?

A: The copper content in 7075 breaks down the protective oxide film, making the alloy more vulnerable in saltwater and industrial atmospheres. Protective finishes such as anodizing or conversion coating are normally applied.

Q: How much more expensive is 7075 than 6061?

A: Typically 25-60% more for equivalent forms, and machining costs are higher because the alloy is harder and more abrasive. The premium is justified where strength is mission-critical.

Q: Can 7075 be formed by bending?

A: Formability is limited in heat-treated tempers and tight bends are discouraged. Parts are usually machined from plate or bar, or formed in the annealed condition and heat treated afterward.

Q: What are the typical mechanical properties of 7075-T6?

A: Published typical values are about 572 MPa ultimate tensile strength, 503 MPa yield strength, 11% elongation, 71.7 GPa modulus, and about 150 HB hardness.