HENAN GNEE NEW MATERIAL CO., LTD
86-372-5055135

Aluminum Foil for Packaging: Blister, Composite Bag and Wrap Grades

Apr 11, 2024

Aluminium foil earns its place in packaging for one reason: it is the cheapest commercially available material that combines a total barrier to light with an almost total barrier to water vapour, oxygen and aroma. A layer only a few thousandths of a millimetre thick can turn a paper or plastic structure into a shelf stable pack. Outside cigarette packaging, the largest uses are aluminium plastic composite bags, medicinal blister packaging and chocolate wrapping, while a number of premium beers also have the bottle neck and mouth wrapped in foil as a decorative and tamper evident finish.

Medicinal Blister Packaging

A push through blister pack is a three part system: a thermoformed plastic cavity that holds the tablet, a lidding foil that seals the cavity, and a heat seal lacquer that bonds the two. The foil is supplied around 0.02 mm thick and is built up as a protective layer, an ink printing layer, the aluminium base material and the adhesive or heat seal layer.

The properties that make this construction suitable for medicines are well established:

Non toxic and compatible with direct contact with the dosage form

Corrosion resistant, so the pack tolerates humid storage and handling

Impermeable to moisture, oxygen and light, protecting light sensitive actives

Heat resistant, so the pack survives drying, printing and sterilisation steps

Printable, so batch number, expiry date and dosage instructions can be applied clearly

Because the print layer sits under a protective lacquer, variable data stays legible through the whole shelf life, which matters for pharmacovigilance and for pharmacy dispensing checks.

Food and Composite Packaging

Aluminium plastic composite bags are the workhorse of food packaging. They are used for snacks and fried foods, for soft cans, and for packaging pharmaceutical tablets and powder, and the same structures are widely applied to ordnance and ammunition packaging precisely because their barrier performance protects contents from moisture over long storage periods.

A composite bag is normally a laminate rather than a single sheet. A typical structure has an outer printable film, an aluminium foil barrier core, and an inner sealant layer that provides the peelable or welded seam. The outer film carries the graphics and resists scuffing, the foil blocks light and vapour, and the sealant controls the opening behaviour of the pack.

Typical Gauge and Structure by Application

Application Typical foil gauge Typical construction
Chocolate and confectionery wrap 0.006 - 0.012 mm Dead soft single foil, plain or lacquered
Pharmaceutical blister lidding 0.020 mm Hard foil with heat seal lacquer and print layer
Aluminium plastic composite bag 0.007 - 0.012 mm Print film / foil / sealant laminate
Bottle neck and mouth wrap Thin decorative gauge Soft foil, printed and embossed

Gauge selection follows the barrier level required, the mechanical abuse the pack will see, and the stiffness the filling line needs. A chocolate wrap that is handled gently can be extremely thin, whereas a laminated bag that must survive stacking and drop testing needs a heavier core or a reinforcing film layer.

Barrier Performance and How It Is Verified

Barrier claims should always be tied to a named test method, because results are not comparable across methods. Water vapour transmission rate is normally determined by an infrared sensor method, oxygen transmission rate by a coulometric sensor method, and light transmission by spectrophotometry. Foil thickness and mechanical properties are verified against the relevant foil specification, and for food contact and medical applications the laminate must also satisfy the applicable migration and hygiene requirements.

In practice a buyer should agree on sample conditioning, test temperature, relative humidity, and whether the result is reported per square metre per day or as a package level figure. A laminate that passes an oxygen barrier test can still fail in service if the seal area is defective, so seal integrity testing on the finished pack is part of the same quality loop.

Export Packing, Storage and Handling

Foil coils and cut sheets are packed to prevent mechanical damage and moisture ingress. Standard practice is to wrap the coil in plastic film or kraft paper and to secure it inside a wooden case or on a wooden pallet, with the outer packaging labelled so that product grade, alloy, temper, gauge and quality information can be read without opening the case.

Reference wooden case size: 1.4 m x 1.3 m x 0.8 m, adaptable to the order

Gross weight per case: approximately 500 - 700 kg, net weight 450 - 650 kg

Special packing requirements can be accommodated by adding the relevant reinforcement

Storage areas should be dry, ventilated and free of condensation. Cases should never be stacked so high that the lower cartons deform, and coils should be lifted with a spreader rather than by the wrap, because a nicked or compressed edge cannot be recovered on the customer line.

FAQ

Q: What thickness of aluminium foil is used for medicinal blister packs?
Pharmaceutical lidding foil is normally about 0.02 mm thick and is supplied with a heat seal lacquer on the sealing side and a protective lacquer over the printed side.

Q: What is the structure of a pharmaceutical blister lidding foil?
It consists of a protective layer, an ink printing layer, the aluminium base material and an adhesive or heat seal layer that bonds to the plastic cavity.

Q: Which aluminium alloys are used for packaging foil?
1235, 8079 and 8011 are the usual packaging grades, supplied in soft temper for wrapping and laminating duty. Alloy choice is based on formability, surface quality and food contact compliance.

Q: Why is aluminium foil used in ammunition packaging?
Because the foil laminate blocks moisture and oxygen, ammunition and ordnance stores more reliably in composite foil packaging than in paper or plain plastic wraps over long storage periods.

Q: How should aluminium foil coils be stored before use?
Keep them in a dry, ventilated area, on the original pallet or case, out of direct contact with the floor, and lift them with a spreader. Avoid stacking that deforms the packaging or the coil edge.

Q: Can a foil laminate replace a rigid container?
For many dry foods and for tablets it can, provided the seal is sound and the pack survives distribution testing. Where the product is fragile or the shelf life requirement is extreme, a semi rigid or rigid format is usually retained.