1050 H14 Aluminum Sheet Plate vs H24: Performance, Forms, and Applications
When comparing aluminum plates for forming and decorative uses, 1050 H14 aluminum sheet plate is often evaluated alongside H24 temper products. GNEE offers both options and helps customers select the optimal temper based on performance and processing requirements.
Overview of 1050 H14 Aluminum Sheet Plate
1050 H14 aluminum sheet plate is a half-hard, strain-hardened aluminum product manufactured through cold rolling. It delivers a combination of surface stability, moderate rigidity, and cost efficiency, making it suitable for applications with relatively simple forming demands.
The alloy's high aluminum purity ensures excellent corrosion resistance and conductivity, while the H14 temper provides improved strength compared to annealed (O temper) material.
1050 H14 Aluminium Chemical Composition
| Element | % Present |
| Cu | 0-0.05 |
| Mg | 0-0.05% |
| Si | 0-0.25% |
| Fe | 0-0.4% |
| Mn | 0-0.05% |
| Zn | 0-0.07% |
| Ti | 0-0.05% |
| Al | Balance |
1050 H14 Aluminium Mechanical Properties
(for sheet thicknesses from 0.2 mm to 6.00 mm)
| Property | Value |
| Tensile Strength | 105–145 MPa |
| Proof (Yield) Strength | Minimum 85 MPa |
| Elongation | Minimum 12% |
| Hardness | Approximately 34 HB |
Note: These values indicate moderate strength, suitable for general-purpose applications.
1050 H14 Aluminium Physical Properties
| Property | Value |
| Density | 2.71 g/cm³ |
| Melting Point | Approximately 650 °C |
| Modulus of Elasticity | About 71 GPa |
| Thermal Conductivity | Around 222 W/m·K |
| Thermal Expansion | 24 × 10⁻⁶ /K |
Supplied Forms of 1050 H14 Aluminum Sheet Plate
GNEE supplies 1050 H14 aluminum plates in multiple configurations:
- Flat aluminum sheets
- Aluminum plates for higher rigidity
- Stucco embossed aluminum sheets
- One-side PVC coated aluminum sheets
- Coils and cut-to-length products
These forms allow the material to adapt to both functional and decorative applications.
Comparison: 1050 H14 Aluminum Sheet Plate vs 1050 H24 Aluminum Plate
| Item | 1050 H14 Aluminum Plate | 1050 H24 Aluminum Plate |
|---|---|---|
| Strength | Higher | Medium |
| Hardness | Higher | Medium |
| Formability | Moderate | Better |
| Deep Drawing | Limited | More suitable |
| Typical Use | Flat panels, signage | Reflectors, enclosures |
H14 is preferred where flatness and rigidity are required, while H24 offers enhanced flexibility for more complex forming operations.
Physical Properties of 1050 H14 Aluminum Sheet Plate
| Property | Value |
|---|---|
| Density | 2.71 g/cm³ |
| Melting Point | ~650°C |
| Elastic Modulus | ~71 GPa |
| Thermal Conductivity | ~222 W/m·K |
| Thermal Expansion | 24 × 10⁻⁶ /K |
These properties support applications requiring lightweight construction and efficient heat transfer.
Advantages and Limitations of 1050 H14 Aluminum Plate
Advantages
- Excellent corrosion resistance for outdoor and marine-adjacent use
- High surface reflectivity for lighting and signage
- Lightweight with good durability
- Cost-effective for large-volume applications
Limitations
- Lower strength than heat-treatable alloys such as 6082-T6
- Poor machinability due to material softness
Common Applications of 1050 H14 Aluminum Sheet Plate
- PS and CTP printing plates
- Aluminum composite panel (ACP) skins
- Battery soft connectors
- Lighting reflectors
- Heat exchanger components
- Cable sheathing and protective covers
Alloy Designations and Standards for 1050 H14 Aluminum Plate
- EN AW-1050 H14
- AA 1050-H14
- UNS A91050
- DIN Al99.5
- ASTM B491
- BS 1B
These standards ensure global compatibility and consistent quality.
1050 Aluminum Sheet Plate Specifications
|
Product Name |
Aluminium sheet |
|
Material |
Aluminum Material |
|
Standard |
GB/T3190-2008, GB/T3880-2006, ASTM B209, JIS H4000-2006, etc. |
|
Model Number |
1050 1060 1100 3003 3004 5051 5052 6061 |
|
Surface |
Bright, polished, hairline, brush, sandblast, checkered, embossed, etching, etc. |
|
Alloy Or Not |
Is Alloy |
|
Technique |
Casting Rolled |
|
Width |
30-1600mm or as your requirement |
|
Length |
2000 mm, 2440 mm, 6000 mm, or as required. |
|
Thickness |
0.5-200mm |
|
Quality control |
Mill Test Certification is supplied with shipment,Third Part Inspection is acceptable. |
Choose the Right 1050 H14 Aluminum Sheet Plate with GNEE
Whether your project prioritizes surface quality, corrosion resistance, or economic efficiency, 1050 H14 aluminum sheet plate remains a dependable choice. With multiple supply forms and strict quality control, GNEE helps customers achieve stable performance across construction, industrial, and electrical applications.
Reach out to GNEE now for expert guidance and customized aluminum plate solutions tailored to your project requirements.
