EN AW 6082 Aluminum Round Bar from GNEE is a heat-treatable Al-Mg-Si-Mn product made by hot extrusion and supplied in the T6 condition. GNEE has supplied extruded aluminum round bar since 2008 and exports to more than 100 countries and regions. This 6082 T6 Round Bar is produced, heat treated and straightened in-house before dispatch.
As a 6082 Aluminum Bar produced to EN 573-3, it is widely specified for construction machinery, transport equipment, industrial automation and machined components. The Al-Mg-Si composition responds well to turning, drilling and slot milling, and the T6 temper gives a strength-to-weight balance suited to load-bearing parts.
Supply covers the diameters in the dimensions section, produced to EN 573-3, EN 755-2 and GB/T 3191-2019, with the material certificate issued at delivery. The grade is also known in the market as 6082 Aluminum Round Rod or 6082 T6 Aluminum Rod.
Send your diameter, length, quantity and destination for pricing.
6082 Aluminum Round Bar Price Reference (SMM)
The metal element follows the SMM A00 base; the conversion charge covers extrusion, T6 heat treatment and finishing. Figures are indicative and confirmed per order.
| Alloy and temper | Diameter | Type | Surface | SMM base | Conversion | Reference CNY/t | Reference USD/t |
|---|---|---|---|---|---|---|---|
| 6082 T6 | 36 mm | Extruded round bar | Mill finish | 22,540 | Extrusion, ageing, finishing | 25,540 – 26,875 | 3,829 – 4,029 |
| 6082 T6 | 100 mm | Extruded round bar | Mill finish | 22,540 | Extrusion, ageing, finishing | 25,540 – 26,875 | 3,829 – 4,029 |
Conversion is indicative and market-dependent. USD figures use USD/CNY 6.67 and are given for comparison only - a contract in USD is converted at the exchange rate on the contract date, so the settled amount can differ from the figures shown here. RMB figures include 13% VAT; the VAT-excluded equivalent is roughly the RMB figure divided by 1.13. Freight, inspection beyond the mill certificate and the trade term are additional. The SMM A00 base shown is the November 18 settlement of 22,540 CNY/t.


Chemical Composition of EN AW 6082 Aluminum Bar
The EN AW 6082 Chemical Composition is defined in EN 573-3 and reported on the material certificate supplied with each lot. Grade AlSi1MgMn Round Bar corresponds to EN AW-6082 under EN 573-3. Its Werkstoff designation is 3.2315 Aluminum Bar.
| Element | Si | Fe | Cu | Mn | Mg | Cr | Zn | Ti | Others each | Others total | Al |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Content (wt%) | 0.70 – 1.30 | ≤ 0.50 | ≤ 0.10 | 0.40 – 1.00 | 0.60 – 1.20 | ≤ 0.25 | ≤ 0.20 | ≤ 0.10 | ≤ 0.05 | ≤ 0.15 | Balance |
The intentional manganese addition of 0.40–1.00% refines the grain structure and is the main metallurgical difference from 6061. Copper is held at or below 0.10% to preserve corrosion resistance.
6082 T6 Aluminum Bar Mechanical Properties
Properties below are EN 755-2 minimums for T6 extruded bar, by diameter. Measured values for the supplied lot appear on the EN 10204 3.1 certificate.
| Diameter d (mm) | Tensile Rm (MPa) min | Proof Rp0.2 (MPa) min | Elongation A (%) min | A50 (%) min |
|---|---|---|---|---|
| d ≤ 20 | 295 | 250 | 8 | 6 |
| 20 < d ≤ 150 | 310 | 260 | 8 | - |
| 150 < d ≤ 200 | 280 | 240 | 6 | - |
| 200 < d ≤ 250 | 270 | 200 | 6 | - |
The 36 mm sample bar falls in the 20–150 mm band: tensile strength at least 310 MPa, proof strength at least 260 MPa and elongation at least 8%. EN AW 6082 has a density of 2.70 g/cm³ and an elastic modulus of approximately 70 GPa. GB/T 3191-2019 lists the same T6 minimums for grade 6082, so the two standards can be cited together.
EN AW 6082 vs 6061 Aluminum Round Bar: Strength, Machinability and Welding Data
Both EN AW-6082 and EN AW-6061 are Al-Mg-Si precipitation-hardening alloys supplied as extruded bar in the T6 condition. Manganese sets them apart: 6082 carries 0.40–1.00% Mn against ≤0.15% in 6061. On EN 755-2 minimums, 6082-T6 is about 19% higher in tensile strength and 8% higher in proof strength than 6061-T6. The 6082 side is listed in the Mechanical Properties table above; the figures below use the same EN 755-2 basis.
| Property (EN 755-2, T6 extruded bar) | EN AW-6082 T6 | EN AW-6061 T6 |
|---|---|---|
| Si (wt%) | 0.70 – 1.30 | 0.40 – 0.80 |
| Mg (wt%) | 0.60 – 1.20 | 0.80 – 1.20 |
| Mn (wt%) | 0.40 – 1.00 | ≤ 0.15 |
| Cu (wt%) | ≤ 0.10 | 0.15 – 0.40 |
| Tensile Rm min (MPa) | See Mechanical Properties table | ≥260 (d ≤ 200 mm) |
| Proof Rp0.2 min (MPa) | See Mechanical Properties table | ≥240 |
| Elongation A min (%) | See Mechanical Properties table | ≥8 |
| Hardness HB (indicative reference) | See Mechanical Properties table | ~90 |
Both alloys can be machined with sharp uncoated carbide tools. The manganese intermetallics and higher strength of 6082 make it slightly more abrasive, while high-volume precision turning often favors 6061. Both grades can be welded by MIG or TIG with ER4043 or ER5356 filler. Welding dissolves or overages Mg2Si in the heat-affected zone of both alloys, leaving local strength below the T6 base-metal level; joints are sized on that reduced value, and procedure qualification follows ISO 15614-2 with quality levels to ISO 10042.
Specification of EN AW 6082 T6 Aluminum Round Bar
| Parameter | Detail |
|---|---|
| Alloy and temper | EN AW-6082 T6; AlSi1MgMn; UNS A96082; DIN 3.2315 |
| Product form | Solid round bar, straight lengths or cut to size |
| Theoretical weight | ~2.75 kg/m at Ø36 mm; actual weight follows dimensional tolerance |
| Process | Hot extrusion, solution heat treatment and artificial ageing; straightened in-house |
| Applicable standards | EN 573-3, EN 755-2, EN 755-3; ASTM B221 and GB/T 3191-2019 on request |
| Surface | Mill finish; anodized finish on request |
| Certificate | EN 10204 3.1; EN 10204 3.2 and third-party inspection can be arranged |
| HS code | 7604.29; final classification is subject to the destination customs authority |
Dimensions & Tolerances of EN AW 6082 Aluminum Round Bar
6082 Aluminum Round Bar Dimensions Chart
| Parameter | Range / value | Note |
|---|---|---|
| Diameter | 6 – 200 mm | Extruded round bar; larger sizes to order |
| Length | 3000 / 6000 mm, or cut to size | Cut lengths made against your list |
6082 Round Bar Tolerance and Straightness
| Parameter | Value | Note |
|---|---|---|
| Diameter tolerance | ±0.20 mm for Ø30–50 mm | EN 755-3 conventional class; confirm against the production line |
| Straightness | ≤0.8 mm/m | Within the usual achievable band; confirm against inspection data |
| Cut-length tolerance | By length band | State the critical length and allowance on the order |
The ranges above are indicative; confirm the exact diameter, tolerance and straightness with the supplier before you release a drawing.
6082 Aluminum Bar for CNC Machining and Precision Parts
Construction machinery: load-bearing pins, shafts and linkage parts, where the 260 MPa proof strength at 36 mm keeps section size down.
Transportation: vehicle and rail structural components and suspension parts that combine low weight with T6 strength.
Industrial automation: machine frames, guide rods, fixtures and roller shafts that need stable dimensions during machining.
CNC machining: bar stock for turning, drilling and slot milling into precision components, with a fine finish taken in the T6 condition.
A 6082 Aluminum Bar for CNC Machining is chosen when the part needs both strength and a machinable stock condition. The T6 temper holds form during cutting while remaining workable with sharp carbide tooling.
Welding and Fabrication of Aluminum 6082 Round Bar
6082 welds by TIG and MIG with ER4043 or ER5356 filler. The heat-affected zone loses part of the T6 strength, so the welded joint is sized on the reduced local value; restoring the original temper across a fabricated assembly needs a full solution heat treatment and artificial ageing cycle, which is assessed against the part drawing. For machining, sharp uncoated carbide tools and clear chip evacuation hold surface finish and size on turned and milled faces.
Processing Services for EN AW 6082 T6 Aluminum Round Bar
The 6082 Extruded Round Bar is produced by direct extrusion and then straightened. Terminology - the term "6082 Drawn Aluminum Bar" denotes cold-drawn (cold-finished) bar, a distinct product form specified to EN 754-2 and ASTM B211/B211M. It differs from the EN 755-2 extruded bar described on this page. Cold drawing gives a tighter diameter tolerance and a brighter surface finish. Mechanical properties stated here apply only to the extruded product; buyers evaluating drawn bar should request separate EN 754-2 mechanical data and availability confirmation.
Custom 6082 Aluminum Round Bar lengths, tempers and end-finishing are handled against the order. Cut-to-size service opens a full bar to the lengths you need, which saves material on repeat orders, samples and repair work; bar is quoted by the piece or by weight in kilograms, and the minimum can be set by weight with no full-ton threshold. Bars can be straightened before dispatch and supplied with an EN 10204 3.1 certificate.
Cutting carries kerf loss and a length tolerance, so critical parts should keep a machining allowance. State the alloy and temper before cutting so the correct stock is released. Specific minimum quantities, cutting charges and unit prices are subject to actual inquiry.
Inspection and Testing of Aluminum 6082 Round Bar
Each lot is checked for diameter, straightness and surface condition before dispatch. The EN 10204 3.1 certificate records the heat analysis and tensile results against EN 573-3 and EN 755-2. Ultrasonic testing, hardness measurement and dimensional checks are carried out on finished bars and recorded; EN 10204 3.2 and third-party inspection can be arranged where the contract calls for them.


Aluminum Round Bar Packaging and Export Protection
Bars are bundled, moisture-wrapped and strapped on export pallets or packed in wooden cases for the sea leg. Each bundle is marked with alloy, temper, heat number and net weight so the pieces sort against the order list on arrival. A packing list, commercial invoice and material certificate accompany the shipment.


About GNEE
Founded in 2008.
Exports aluminum products to more than 100 countries and regions.
GNEE is a 6082 Aluminum Round Bar Manufacturer with in-house extrusion and machining capability.
One-stop supply across round bar, plate, tube and fabricated parts on a single set of documents.
Export packaging and documentation are prepared in-house for the destination port.

Request a Quote for 6082 Aluminum Round Bar
As a direct 6082 Aluminum Round Bar Supplier, GNEE works from the order drawing. Sizes and quantities on the drawing are enough to price the order.
Quotations are benchmarked to SMM, with the metal element confirmed against the SMM A00 quote on the order date. MOQ is flexible - small trial orders and large-volume orders, full container loads and long-term contracts are all accepted. Lead time is 15–30 days. An EN 10204 3.1 mill test certificate comes with each order, and FOB or CIF terms with T/T or L/C payment are available.
Send diameter, length, quantity, temper and destination - we reply within 24 hours.
FAQ
Q: Is EN AW-6082 the same grade as 6082-T6?
A: EN AW-6082 is the European designation for the AlSi1MgMn alloy under EN 573-3. GB/T 3191-2019 lists the same alloy as grade 6082. T6 means solution heat treated and artificially aged. The designation and the temper are both stated on the material certificate.
Q: Which temper is supplied, and can other tempers be ordered?
A: The standard supply is T6. Other tempers are quoted against the required mechanical properties and quantity. The temper is stated on the material certificate and should be written on the order.
Q: Which standards apply to the bar?
A: Chemical composition is specified to EN 573-3, mechanical properties of extruded bar to EN 755-2, and dimensional tolerances to EN 755-3. ASTM B221 applies to extruded bar for North American buyers, and GB/T 3191-2019 where the Chinese standard is called up.
Q: What is the minimum order quantity?
A: MOQ is flexible: small trial orders, full containers and long-term contracts are all accepted. For cut-to-length bar the minimum can be set by weight in kilograms with no full-ton threshold. The applicable quantity is confirmed in the quotation.
Q: What is the lead time?
A: Standard lead time is 15 to 30 days, counted from order confirmation and depending on diameter, length and quantity.
Q: Can you cut the bar to a specified length?
A: Yes. Whole bars are cut to the requested length, which reduces waste on repeat orders, samples and repair work. Cutting loss and length tolerance apply, so critical parts need machining allowance. State the alloy and temper before cutting. Prices are subject to actual inquiry.
Q: Does 6082-T6 round bar machine well?
A: The Al-Mg-Si composition machines well in the T6 condition, so the bar is supplied for turning, drilling and slot milling. Use sharp carbide tools and clear chips to hold surface finish and dimensional accuracy.
Q: How is the bar inspected before shipment?
A: Each lot is supplied with an EN 10204 3.1 certificate recording composition and mechanical test results. Ultrasonic testing, hardness measurement and dimensional checks are carried out in-house. EN 10204 3.2 and third-party inspection can be arranged.
Q: How is the bar packed for export?
A: Bars are bundled, moisture-wrapped and strapped on export pallets or in wooden cases. Each bundle is marked with alloy, temper, heat number and net weight. Packing list, invoice and material certificate accompany the shipment.
Q: What pricing and payment terms apply?
A: Prices are linked to SMM and quoted FOB or CIF, with T/T or L/C terms. Send diameter, length, quantity and destination to receive a quotation. GNEE replies within 24 hours.
Hot Tags: en aw 6082 aluminum round bar, China en aw 6082 aluminum round bar manufacturers, suppliers, factory












